Dinogy Graphene 4S 1500 mAh 65 C - Front View

Battery review: Dinogy Graphene 4S 1500 mAh 65 C

Publiziert von Nils Waldmann

am

It has been some time since my last Dinogy battery review. Now that the flying season is coming on strong in most parts of the world, we also finally can expect new FPV racing battery products. No surprise on this matter, that Dinogy just sent me their new GRAPHEN series, developed to be a cost-efficient solution for more price-sensitive pilots. This review is looking at the newest version of the 1500 mAh of the Dinogy Graphene 4S 65 C pack.

How to use charts:

 

Attention

This battery review contains some charts which can be interactively utilized. You are able to:

  1. Highlight any value just by clicking on the corresponding key below the chart.
  2. Hover over any value / line inside the chart to get precise readings.
  3. Right axis is always current.

Have fun! :)

Appearance

The brand new Dinogy Graphene series comes in the usual card board box, packed within bubble wrap and protected by a layer of foam on the bottom. Dinogy lipos have always been one of the products with the best packaging – so no surprises here. The battery itself, aiming to be cost-efficient, is packed in an all black shrink wrapping. The red honey-comb style materials on the sides are still in place, identifying the battery as a Dinogy product. What I can’t praise enough is the fact that even the economical Dinogy Graphene series has all the important information printed on a small sticker, which is attached to the back of the pack. The overall built-quality is very good – nothing to worry about.

Technical Design

The Dinogy* Graphene 65C pack is a standard 4S1P config flight pack for high power use. It utilizes the newest generation graphene cell chemistry. An extra layer of carbon particles is added to minimize internal resistance and hence maximize possible current draw. The new Graphene series now is rated up to 65C constant load, which is 10C less than the last years MEGA series.

Build Quality: Very good. Pack feels very well made on the outside. Connection terminal looks solid. The bright red honey-comb materials feels like it offer good protection on the sides.

Plugs: The Dinogy pack comes with standard XT60 connectors* equipped.

Cables: L&E uses 12 AWG wires on this packs. The high flexible silicon layer is rated up to 200°C. Cable length is about 7.5 centimeters.

Balancing plugs: Standard XT-system. Balance wires are short (2.5 cm) which is a benefit in terms of getting them out of the prop-range on the aircraft. Both, main power cables and balancer wires, are connected to the top edge of the pack.

Technical Details

ManufacturerL&E Battery Industrial*
TypeDinogy Graphene 65C
Cell chemistryLithium Polymere (LiPo)
Cell typeDinogy Graphene enabled chemistry
Cell count4
Pack configuration4S1P
Capacity1500 mAh
Max. charge current7.5 A
Discharge current continuous97.5 A
Max. discharge current-
Weight (incl. plugs)ca. 176 grams
Measurements listed
27 x 34 x 87 mm
Measurements measured
34 x 29 x 94 mm
PriceUS-$ 19
Dealer-
NoteThis battery has been directly donated by the manufacturer / distributor for review purposes.

Impressions

Dinogy Graphene 4S 1500 mAh 65 C - Front View
Dinogy Graphene 4S 1500 mAh 65 C - Back
Dinogy Graphene 4S 1500 mAh 65 C - Bottom View
Dinogy Graphene 4S 1500 mAh 65 C - Top View
Dinogy Graphene 4S 1500 mAh 65 C - Connection Terminal

(Click to enlarge.)

Break-in documentation

The battery followed the standard break-in-process: The pack is charged at a rate of 1C until CV-phase ends with current of 1/10C. The break-in phase consists of four charging cycles at 1C and four corresponding discharges at 1 C / 4C / 10C and 20 C.

Anomalies: No anomalies during break-in.

Charging process

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden


CV-Phase is short on this cell type. Balancing in normal mode took 2:20 min. Cell drift during charge was unobtrusive. This is for 1C charge (1.5 A).

Load Testing

The main part of this battery test will consists of different load test settings showing the battery performance. Constant load testing is used to judge the advertised C-ratings as well as look at cell drift under high loads. We also check on internal resistance once more. Next up is the dynamic current test, which simulates a „real“ flight with changing (=dynamic) loads. For test methodology please check the dedicated methodology page!

Constant Load Testing

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Constant load testing follows a certain load pattern of different constant currents. Base load is 10 C. Current pulses at 50 C, 35 C, 20 C and 30 C are maintained for time intervals between 10 and 20 seconds. For more details please refer to the test methodology page.

Capacity Usage

During this test the pack delivered 1094 mAh. This is 72,9 % of nominal capacity. A good result.

Average cell voltages

The following table lists the average voltages per cell, of the total pack, as well as the averaged value per cell as fraction of total voltage during phase of active load.

Cell 1Cell 2Cell 3Cell 4TotalAverage per cell
Avg. Voltages3.749 V3.748 V3.752 V3.749 V14.998 V3.750 V

Just looking at average values the Dinogy pack performs fine. All cells stayed well above 3,7 V on average. An average value above 3,74 V / cell can be considered very good.

Focus Voltages

Exceptionally interesting when testing a battery under a constant load for a longer period of time: the lowest voltage per cell just before load impulse is disabled. On top, you should have look at voltage recovery rate, that is: how fast do cell voltages rise again once load impulse is cut.

PhaseCell 1Cell 2Cell 3Cell 4Total
End of 50 C3.572 V3.570 V3.609 V3.622 V14.373 V
End of 35 C3.536 V3.537 V3.555 V3.560 V14.187 V
End of 20 C3.316 V3.342 V3.247 V3,290 V13.978 V
End of 30 C----

Voltage sag is very low on the Dinogy Graphene 65C 1500 mAh pack. No cell went below 3,5 V/cell benchmark on first two load cycles.

Average voltage recovery per second

Those values are specific to the test setting and not valid for the pack in general! Still they allow an estimated guess about how fast voltages rise again after current spikes.

Cell 1Cell 2Cell 3Cell 4Total
Avg. Recovery0.0347 V / s0.0344 V / s0.0210 / s0.0190 V / s0.0888 V /s

Voltage recovery is quick for the new Graphene 1500 mAh 65 C battery.

IR-Measurement

IR measurement is conducted using the four current pulses. Resistance for each cell is calculated in all four discharge phases. Shown values are averaged to cancel out different temperature points due to different discharge states during measurements.

Cell1234Total
Resistance [mΩ]2.642.582.2262.329.80

Interpretation: The internal resistance of 2.45 mΩ average per cell indicates a „true“ C-rating of around  40 C (60.6 A). This is on the conservative side and represents a current draw that will make the pack last for a long time. Overall performance can be described as very high. The pack achieved equal or higher values compared to competitor products claiming to have 75C or higher ratings.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Cell drift under load

Discharge Phase50 C35 C20 C30 C
Max Cell drift (V)0.024 V0.025 V0.095 V-

Cell drift is low on the new Dinogy Graphene 65 C pack during main discharge phase. All cells are matched well, cell 1 seemed to be a little off, though.

Key Temperature Facts

Temperature Development - Dinogy Graphene 4S 1500 mAh 65C
Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Temperature Development

Max. temp during discharge was around 59.2 °C on top of pack. Note that heating of stressed LiPo packs will continue for some more time even when load is cut.

Market Comparison

The following chart shows all reviewed LiPos in the same product segment for direct comparison of performance. Higher values under load are better.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Constant 25 C Discharge

Pretty much a standard benchmark in the LiPo industry.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden


Cut-Off /warning value for this battery should be chosen 3.5 V minimum. After this point voltage drops quick. The battery provided 1094 mAh (72,9 %) during the 25 C discharge.

Market Overview

Comparison of different reviewed 1500 mAh batteries under 25 C load.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Dynamic Load Testing

The dynamic load testing setting consists of two separate discharge scenarios that have been developed of two different real-life FPV flights. Pattern one represents a high speed low proximity flight around the open field with some hovering to the end. Average load is around 22 A. Second pattern is a free-style flight around trees in the park with some current spikes near 70 A. Average load on this flight is around 13 A due to longer floating periods.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Capacity Usage

During the test of pattern 1 the pack delivered 1101 mAh. This is 73.4 % of nominal capacity. Good! In patter 2 testing 1068 mAh (71.2 %) could be used until first cell reached cut-off voltage.

Market Comparison

The following charts give an overview of all tested packs in the 1500 mAh class so far.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

The last chart of this review sums up the usable capacity during all four load scenarios. Please note that this is only the capacity consumed by the electronic load! There are losses due to heating of the pack, which could be approximated (see testing methodology page). All four tests are cut when any cell goes below cut-off voltage of 3,3 V (or pack goes above 58 °C on any of the three probes). If you would push further and go down to 3,0 V/cell you will be able to squeeze out some mAh more, but at the cost of excessive heat generation and shortening of pack life-span. This value will most likely differ from what you get when flying on a quad as most people don’t monitor voltage on a per cell basis and therefore don’t even notice if voltage drops below 3,3 V/cell during punsh-outs (what’s not necessarily a good thing, though). For comparison, used capacity until 3,3 V/cell is reached is the base line in all battery reviews on Drone-Zone.de.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Conclusion

The all new Dinogy Graphene* 4S 1500 mAh 65C battery is a small sized pack with a capacity to weight ratio of 8.5 mAh/g. As other graphene enabled packs this battery tends to be just a little heavier than a “standard” lipo. Build quality of this new „best value“ battery is still excellent. The pack is rectangular shaped and keeps it shape under every load situation – no puffing what so ever! Voltage stability is good on the Graphene 65C version. Cut-off should be chosen at 3,5 V / cell minimum.

Usable battery capacity is decent, higher priced pack will yield in a little more output, though. Cell matching is fine, nothing to complain about here.The rating of 65C is a bit over the top, of course. I would rate this pack at very amazing 40 C continuous. This allows you to pull around 60.6 A without having to worry about the packs health too much. More than enough head room for most of the applications out there and a good balance between performance and costs. As you can see in the dynamic loads higher current spikes are handled well. Compared to the 1300 mAh version, the 1500 mAh Dinogy Graphene* pack tended to get a lot warmer.

For around 19 US-$ (retail price) this pack is certainly will hit the market running.  It outperforms the some of the competitor products without any problems, but keeps in line behind the Dinogy MEGA and ULTRA series* (nothing other than I would habe expected). In the end 19 dollars (US) are almost a no-brainer, especially for a battery that might be used regularly in training or freestyle situations around the park, where there is no competitive pressure as on the race track.

Other packs of this line up tested:

Bleibt in Kontakt!

Wenn ihr über die neuesten Drohnen-News, Drohnen-Leaks, Drohnen-Gerüchte, Drohnen-Guides und Drohnen-Testberichte auf dem Laufenden bleiben möchtet, dann folgt uns gerne auf unseren Social-Media-Kanälen!

Außerdem freuen wir uns natürlich über eure Nachrichten oder Fragen in den Kommentaren!


Hinweis: Mit Sternchen (*) markierte Links sind Affiliate-Links / Partnerlinks. Mit einem Kauf über diesen Link erhalten wir als Seitenbetreiber eine Verkaufsprovision. So kannst du Drone-Zone.de ganz einfach unterstützen. Bitte beachtet, dass es sich bei Drone-Zone um eine reine Website zur Information und keinen Online-Shop handelt. Ihr könnt über unsere Seite keine Kaufverträge über die dargestellten Artikel abschließen und auch keine persönliche Beratung hierzu in Anspruch nehmen. Mehr Informationen dazu findest du hier.

Avatar-Foto

Nils Waldmann

Hi, ich bin Nils! Ich bin leidenschaftlicher Modellbauer, Hobby-Fotograf, Akku-Liebhaber und RC-Pilot. Ich berichte hier über die neusten Entwicklungen in der Drohnen-Branche und kümmere mich um detaillierte Anleitungen, Guides und Testberichte.

Schon gesehen?

DJI Drohnen-Akkus in Form des DJI Logos

Alle DJI Drohnen-Akkus im Vergleich (2024)

Drohnen-Akkus sind die Energiequelle jedes Multicopters. Ohne die Akkumulatoren auf Lithium-Polymere-Basis hebt keine moderne Drohne ab. In diesem Artikel haben wir dir eine Übersicht aller Drohnen-Akkus für aktuelle DJI Drohnen ... jetzt lesen!

Dinogy Graphene 2.0 4S 1300 mAh 70C PT - Front Side

Battery review: Dinogy Graphene 2.0 4S 1300 mAh 70C (Prototype)

I am proud to present you a first review of the all new Dinogy Graphene 2.0 batteries, that have been developed in dedication to all of us FPV racers. The ... jetzt lesen!

Battery test methodology (How we test LiPo batteries)

This page contains all the details about how lipo batteries are tested and what methodology is used.It is meant for those of you, who want to know exactly what is ... jetzt lesen!

DroneLab CHAOS Edition 4S 1500 mAh 75-150 C - Front

Battery review: Drone Lab CHAOS Edition 4S 1500 mAh 75-150C

UK distributor and RC manufacturer RadioC has its newest Drone Lab CHAOS Edition lipo packs out on the market. The Drone Lab series is specifically designed for use in race ... jetzt lesen!

Schreibe einen Kommentar