Dinogy Graphene 2.0 4S 1800 mAh 70C - Front

Battery review: Dinogy Graphene 2.0 4S 1800 mAh 70 C

Publiziert von Nils Waldmann

am

After reviewing the very promising prototype of the new Dinogy Graphene 2.0 packs, the time has finally come and I received samples of the final battery product. This review is looking at the 1800 mAh version of the all new Dinogy Graphene 2.0 4S 70 C pack.

How to use charts:

This battery review contains some charts which can be interactively utilized. You are able to:Attention

  1. Highlight any value just by clicking on the corresponding key below the chart.
  2. Hover over any value / line inside the chart to get precise readings.
  3. Right axis is always current.

Have fun! :)

Appearance

The final version of the Dinogy* Graphene 2.0 pack looks a little different than the prototype tested earlier. The black shrink wrapping has been switched for a light grey one. Also the graphic sticker has been re-done, looking a lot more professional now. I am very happy to see though, that they decided to keep the cool looking, red, honey comb-style materials on the sides. On the back you now find a sticker that provides all the important information how to handle the battery. I really appreciate to see this stuff printed onto the pack. A lot better than giving out a small piece of paper as many other manufacturers tend to do. The packs come in a high quality card box with a foam layer on the bottom. The pack itself is packed in bubble wrap. Also it is made sure by a little piece of foam that the XT60 connector stays in place and can’t damage the pack during transport.

Technical Design

The Dinogy Graphene 2.0 70 C pack* is a standard 4S1P config flight pack for high power use. It utilizes the new generation graphene cell chemistry. An extra layer of carbon particles is added to minimize internal resistance and hence maximize possible current draw.

Build Quality: Very good. Pack feels very well made on the outside. Connection terminal looks solid. The read honey-comb materials feels like it offer good protection on the sides.

Plugs: The Dinogy pack comes with standard XT60 connectors* equipped.

Cables: L&E uses 12 AWG wires on this packs. The high flexible silicon layer is rated up to 200°C. Cable length is about 8 centimeters.

Balacing plugs: Standard XT-system*. Balance wires are very short (3 cm) which is a benefit in terms of getting them out of the prop-range on the aircraft. Main power line and balancer wires are both connected to the top of the pack.

Technical Details

Manufacturer L&E Battery Industrial* Dinogy Graphene 2.0 4S 1800 mAh 70C - Front

Dinogy Graphene 2.0 4S 1800 mAh 70C - Back

Dinogy Graphene 2.0 4S 1800 mAh 70C - Terminal

Dinogy Graphene 2.0 4S 1800 mAh 70C - Top

Dinogy Graphene 2.0 4S 1800 mAh 70C - Bottom

(Click to enlarge.)

Type Dinogy Graphene 2.0 70C
Cell chemistry Lithium Polymere (LiPo)
Cell type Dinogy Graphene enabled chemistry
Cell count 4
Pack configuration 4S1P
Capacity 1800 mAh
Max. Charge Current  9 A
Max. Discharge Current
Continuous
Burst
126 A
? A
Weight
w/o plugs
with plugs

ca. 201 grams
Measurements
as listed
measured
33 x 35 x 90 mm
31.8 x 34 x 90 mm
Price ~ 37 €
Note This battery has been directly donated by the manufacturer / distributor for review purposes.

Break-in documentation

The battery followed the standard break-in-process: The pack is charged at a rate of 1C until CV-phase ends with current of 1/10C. The break-in phase consists of four charging cycles at 1C and four corresponding discharges at 1 C / 4C / 10C and 20 C.

Anomalies: No anomalies during break-in.

Internal resistance measurements during break-in phase via iCharger 406B at 40°C pack temperature

Cycle Cell 1 Cell 2 Cell 3 Cell 4 Total
After first charge  4.9  5.2  4.9  5.2 20.0
After second charge  4.9  5.0  5.0  5.5 20.4
After third charge  5.0  4.9  5.0  5.1 20.0
After fourth charge  4.9  4.8  4.9  5.0 19.6

Charging process

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden


CV-Phase is short on this cell type. Balancing in normal mode took 2:06 min. Cell drift during charge was unobtrusive. This is for 1C charge (1,8 A).

Load Testing

The main part of this battery test will consists of different load test settings showing the battery performance. Constant load testing is used to judge the advertised C-ratings as well as look at cell drift under high loads. We also check on internal resistance once more. Next up is the dynamic current test, which simulates a „real“ flight with changing (=dynamic) loads. For test methodology please check the dedicated methodology page!

Constant Load Testing

Constant load testing follows a certain load pattern of different constant currents. Base load is 10 C. Current pulses at 50 C, 35 C, 20 C and 30 C are maintained for time intervals between 10 and 20 seconds. For more details please refer to the test methodology page.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Capacity Usage

During this test the pack delivered 1323 mAh. This is 73.4 % of nominal capacity. A very good result.

Average cell voltages

The following table lists the average voltages per cell, of the total pack, as well as the averaged value per cell as fraction of total voltage during phase of active load.

Cell 1 Cell 2 Cell 3 Cell 4 Total Average per cell
Avg. Voltages 3.734 V  3.732 V  3.730 V  3.730 V  14.926 V 3.731

Just looking at average values the Dinogy pack* performs well. All cells stayed above or at 3.73 V on average. An average value above 3.73 to 3.75 V / cell can be considered very good in this class.

Focus Voltages

Exceptionally interesting when testing a battery under a constant load for a longer period of time: the lowest voltage per cell just before load impulse is disabled. On top, you should have look at voltage recovery rate, that is: how fast do cell voltages rise again once load impulse is cut.

Phase Cell 1 Cell 2 Cell 3 Cell 4 Total
End of 50 C  3.51 V 3.508 V 3.519 V 3.552 V 14.089 V
End of 35 C 3.512 V 3.513 V 3.52 V 3.536 V 14.081 V
End of 20 C 3.281 V 3.28 V 3.264 V 3.289 V 13.114 V
End of 30 C

The average cell voltage stability on the Dinogy pack can be considered very good. No cell fell below the benchmark threshold of 3.5 V during the first two current pulses.

Average voltage recovery per second

Those values are specific to the test setting and not valid for the pack in general! Still they allow an estimated guess about how fast voltages rise again after current spikes.

Cell 1 Cell 2 Cell 3 Cell 4 Total
Avg. Recovery [V/s]  0.027 0.027 0.0263 0.022 0.1035

Excessive voltage sag isn’t a problem for this battery. Recovery rates after current pulses are decent, too.

IR-Measurement

IR measurement is conducted using the four current pulses. Resistance for each cell is calculated in all four discharge phases. Shown values are averaged to cancel out different temperature points due to different discharge states during measurements.

Cell 1 2 3 4 Total
Resistance [mΩ]  2.57 2.53 2.47 2.59 9.27

Interpretation: The internal resistance of 2.54 mΩ average per cell indicates a „true“ C-rating of around 36.2 C (65.2 A). A very good value. This calculation is on the conservative side and represents a current draw that will make the pack last for a long time. The pack had no problems delivering during high C discharge pulses. Cell matching is almost perfect on this pack.

Cell drift under load

Discharge Phase 50 C 35 C 20 C 30 C
Max Cell drift (V) 0.019 V 0.035 V 0.028 V  –

The Dinogy Graphene 2.0* 4S 1800 mAh 70 C has a very low drift during main discharge phase. Even to the very end of the cycle cells drift is almost neglect-able.

Key Temperature Facts

Temperature Development - Dinogy Graphene 2.0 4S 1800 mAh 70C

Temperature Development

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

All temperature probes reported values below cut-off point at 58°C. Max. temp during discharge was around 54.9 °C on top of pack. Note that heating of stressed LiPo packs will continue for some more time even when load is cut.
Market Comparison

The following chart shows all reviewed LiPos in the same product segment for direct comparison of performance. Higher values under load are better.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Constant 25 C Discharge

Pretty much a standard benchmark in the LiPo industry.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Cut-Off /warning value for this battery should be chosen 3.5 V minimum. After this point voltage drops very quick. The battery provided 1318 mAh (73.2 %) during the 25 C discharge. A great result.

Market Overview

Comparison of different reviewed 1800 mAh batteries under 25 C load.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Dynamic Load Testing

The dynamic load testing setting consists of two separate discharge scenarios that have been developed of two different real-life FPV flights. Pattern one represents a high speed low proximity flight around the open field with some hovering to the end. Average load is around 22 A. Second pattern is a free-style flight around trees in the park with some current spikes near 70 A. Average load on this flight is around 13 A due to longer floating periods.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Capacity Usage

During the test of pattern 1 the pack delivered 1337 mAh. This is 74.3 % of nominal capacity. A good very value. In patter 2 testing 1353 mAh (75.2 %) could be used until first cell reached cut-off voltage. Very good again!

Market Comparison

The following charts give an overview of all tested packs in the 1800 mAh class so far.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

The last chart of this review sums up the usable capacity during all four load scenarios. Please note that this is only the capacity consumed by the electronic load! There are losses due to heating of the pack, which could be approximated (see testing methodology page). All four tests are cut when any cell goes below cut-off voltage of 3,3 V (or pack goes above 58 °C on any of the three probes). If you would push further and go down to 3,0 V/cell you will be able to squeeze out some mAh more, but at the cost of excessive heat generation and shortening of pack life-span. This value will most likely differ from what you get when flying on a quad as most people don’t monitor voltage on a per cell basis and therefore don’t even notice if voltage drops below 3,3 V/cell during punsh-outs (what’s not necessarily a good thing, though). For comparison, used capacity until 3,3 V/cell is reached is the base line in all battery reviews on Drone-Zone.de.

Google Docs

Mit dem Laden des Diagramms akzeptieren Sie die Datenschutzerklärung von Google.
Mehr erfahren

Diagramm laden

Conclusion

The all new Dinogy Graphene 2.0 4S 1800 mAh 70C* battery is a usual sized pack with a decent capacity to weight ratio of 8.95 mAh/g. As other graphene enabled packs this battery tends to be just a little heavier than a „standard“ lipo. Build quality of this battery is excellent. The pack is rectangular shaped and keeps it shape under every load situation. No puffing what so ever! I personally like the new design combining the light grey with the red honey-comb reflector materials at the sides. Voltage stability is great on the final Graphene 2.0 version. Cut-off should be chosen at 3,45 V / cell minimum. The sticker on the pack tells you 3,4 V/ cell but this would mean to cut of throttle immediately after you hear your telemetry or buzzer complaining. Usable battery capacity is the best of all packs testes within the 1800 mAh class so far. Cell matching is almost perfect on this pack*, good job! The rating of 70C is a little over the top, of course. I would rate this pack at still very solid 36 C continuous. This allows you to pull around 66 A without having to worry about the packs health too much. You would have to punch out most of the smaller quads pretty hard to get that kind of load on a constant basis. As you can see in the dynamic loads higher current spikes are handled well, too.  For around 37 € this pack is certainly not the cheapest battery you can buy – but also not the most expensive. On the other hand the Graphene 2.0 1800 mAh version* is the best battery in this class I have reviewed so far. That’s not only true for performance, but also for overall product quality. In the end about 37 euros are still a fair price for a battery pack of this performance level.

Other packs of this line up tested:

Bleibt in Kontakt!

Wenn ihr über die neuesten Drohnen-News, Drohnen-Leaks, Drohnen-Gerüchte, Drohnen-Guides und Drohnen-Testberichte auf dem Laufenden bleiben möchtet, dann folgt uns gerne auf unseren Social-Media-Kanälen!

Außerdem freuen wir uns natürlich über eure Nachrichten oder Fragen in den Kommentaren!


Hinweis: Mit Sternchen (*) markierte Links sind Affiliate-Links / Partnerlinks. Mit einem Kauf über diesen Link erhalten wir als Seitenbetreiber eine Verkaufsprovision. So kannst du Drone-Zone.de ganz einfach unterstützen. Bitte beachtet, dass es sich bei Drone-Zone um eine reine Website zur Information und keinen Online-Shop handelt. Ihr könnt über unsere Seite keine Kaufverträge über die dargestellten Artikel abschließen und auch keine persönliche Beratung hierzu in Anspruch nehmen. Mehr Informationen dazu findest du hier.

Avatar-Foto

Nils Waldmann

Hi, ich bin Nils! Ich bin leidenschaftlicher Modellbauer, Hobby-Fotograf, Akku-Liebhaber und RC-Pilot. Ich berichte hier über die neusten Entwicklungen in der Drohnen-Branche und kümmere mich um detaillierte Anleitungen, Guides und Testberichte.

Schon gesehen?

Akkuladegerät - Junsi iCharger Teaser

Akkuladegerät für Drohnen: Worauf Du achten solltest

Dein Akkuladegerät bestimmt nicht nur, wie lange du zum Laden eines Flugakkus benötigst, es sorgt auch dafür, dass deine Lithium-Akkus sicher aufgeladen werden. In diesem Artikel nennen wir dir, die ... jetzt lesen!

Dinogy Graphene 2.0 4S 1300 mAh 70C PT - Front Side

Battery review: Dinogy Graphene 2.0 4S 1300 mAh 70C (Prototype)

I am proud to present you a first review of the all new Dinogy Graphene 2.0 batteries, that have been developed in dedication to all of us FPV racers. The ... jetzt lesen!

Dinogy Graphene 4S 1300 mAh 65 C - Front View

Battery review: Dinogy Graphene 4S 1300 mAh 65 C

It has been some time since my last Dinogy battery review. Now that the flying season is coming on strong in most parts of the world, we also finally can ... jetzt lesen!

SLS NOC FPV Battery Series

SLS präsentiert SLS-NOC FPV Race LiPo Akkus

Der deutsche LiPo-Akkuhersteller SLS (Stefans Lipo Shop) hat seine neue FPV-Racing Akkuserie vorgestellt. Bei SLS geht man damit einen neuen Weg und verabschiedet sich endgültig vom C-Rating als Leistungsangabe. Die ... jetzt lesen!

Schreibe einen Kommentar